View and Download Buell XB Series service manual online. XB Series Motorcycle pdf manual download. See a Buell service manual for proper torque values. Aftermarket . Typical Buell V.I.N.: Ulysses Models Ignition System: XB Models. ITEM. DATA. T+ .com/

Author: Akigis Mejind
Country: Nigeria
Language: English (Spanish)
Genre: Travel
Published (Last): 14 September 2011
Pages: 256
PDF File Size: 11.23 Mb
ePub File Size: 8.49 Mb
ISBN: 983-3-69527-395-7
Downloads: 44887
Price: Free* [*Free Regsitration Required]
Uploader: Nirisar

Install horn and tighten fasteners to in-lbs Nm. Fork Holding Tool Record rider suspension settings before disassembly. Open Starter Armature Test 1. Replace commutators when diameter is less than 1.

Remove assembly from motorcycle. Install new retaining ring in groove of outer buell-firebolt-seevice-manual hub. Please comment on the completeness, accuracy, organization, usability, and readability of this manual.

While riding, a loose seat can shift Remove seat lock clip 1 by sliding from seat lock plate causing loss of control, which could result in death or 6. Wheel bearing backing plate Figure Remove sprocket cover fasteners and washers 1, 3. Canister Mounting Bracket 1. The result is that The purpose of the clutch is to smoothly disengage and engage the rotational force of the clutch shell is transmitted through the engine from the rear wheel for starting, stopping and shifting the clutch plates to the clutch hub.

Buell Firebolt Service Manual

Install upper rocker cover using screws with washers and new fiber seals 5. Upper fork clamp Figure Connect battery positive cable red first, tightening to filegype Nm. Repeat to verify torque. Socket head fastener 7.

Buell XB Models Service Repair Workshop Manual DOWNLOAD─影片 Dailymotion

Install right tail section 16 onto vehicle. The socket and pin housings of all other connectors are inter- changeable, that is, the black may be mated with the gray, since the alignment tabs are absent and the orientation of the external latch is the same. Turn key ON for two seconds. Interactive exhaust cable bracket translucid cover only Actuator Screws Lightning XB12 models with translucid cover only Figure NOTE Do not operate front brake lever with front wheel removed or caliper pistons may be forced out.

  DICCIONARIO LACANIANO DYLAN EVANS PDF

Ground terminal fastener 2 7. When wear bars become visible and New tires should be stored in a horizontal tire rack.

Install Nut Typical Figure Inside the damper rod assembly 6 is a fork push rod 4 that is tapered on one end to control the movement of fluid in the front fork increasing and decreasing the damping properties. Muffler Mounting System Fan actuation is controlled by the ECM. Install upper rocker covers 6. The exhaust enters 2 the muffler and flows 3 through the open valve 1 into chamber C 7 and then The interactive exhaust system is standard equipment on the exits 8.

Once engine has been removed from vehicle, finish sm removing the following items as required: Rear brake fluid reservoir Figure Remove front sprocket cover. Install Adapter Typical sm sm 1. There are two types of connectors in this series: If, through hard usage, the primary chain does become worn and cannot be adjusted to within specifications, it must be replaced.

Replace with new o-rings. Remove idler pulley bracket nuts and washers 5 from studs 3. Upper fork clamp pinch fastener 2 Figure Pump brake hand lever to drain brake fluid.

Electronic control module ECM. Tighten brake caliper banjo bolt 2 and master cylinder bore are clean and undamaged before metric to ft-lbs Nm.

  BAIXAR O FESTIM DOS CORVOS PDF

Each assembly has an internal compression spring which supports the forward weight of the vehicle and rider. Main drive gear 2.

Headlight support bracket 1. Servicing of transmission compon- ents requires removing the engine and disassembling splitting the crankcase.

Welcome to our Buell forum! Shop performance motorcycle parts.

If the crankcases are being separated it sm will be necessary to remove rear isolator assembly by removing the forward two fasteners first and then the two rear fasteners re-install with new fasteners. Vertical Alignment pd Figure Install oil pump buell-firebolt-esrvice-manual and all gears and onto right crank- sm case half, install fasteners and tighten.

This helps the rider establish the relative distance of Loosen mount 3 and remove from bracket 4. Install battery cables to battery: When removing and installing the left air buell-firebolt-servjce-manual, the alternator and voltage regulator harnesses and connections are secured Remove three engine shroud air scoop fasteners 5.

2008 Buell XB Models Service Repair Workshop Manual DOWNLOAD

When wear bars become visible and recommends that you see your dealer for these services. Wear safety buell-fiebolt-service-manual when working with compressed air. Secure stator using four new stator fasteners 1.

Rear caliper mounting fasteners 2. Remove shock reservoir fasteners and feed the reservoir out of subframe tail assembly.